Forum Post: RE: AM62L: Discussion for Non-Muxed Asynchronous Interface...
Thanks for the update. For the HPI interface with GPMC connection. Based on the above thread and block diagram. We can interface GPMC in AM62L and HPI. But as per above diagram the HPI CNT pins are...
View ArticleForum Post: RE: TDA4VH-Q1: Read of MHDP__MHDP_APB_REGS__KEEP_ALIVE_P Register...
Hi Arvind, As discussed in the last call, let me check this with the team internally. Regards, Brijesh
View ArticleForum Post: RE: TDA4VH-Q1: DSS PDK dss_display_test is successful but no...
Hi Aravind, But for which interface are you seeing this issue? Are you using DP output interface? But if i recollect, you were seeing hang on updateAlive API, is it resolved? Additionally, is link...
View ArticleForum Post: RE: TDA4VH-Q1: DSS PDK dss_display_test is successful but no...
HI Brijesh, For the sample dss_display_test.c, we are not facing hang issue in updateAlive. But for the DSS_Init called from our application code we are facing the hang issue on updateAlive still. May...
View ArticleForum Post: RE: TDA4AL-Q1: J7EXPE01EVM board's HDMI output is not working.
Hi Petervera, I really dont think we support this board to get the HDMI output. Regards, Brijesh
View ArticleForum Post: RE: TDA4VH-Q1: TDA4VH:Memory read and write QOS configuration for R5
Hi Li Quan, That's great. As such Display ISR does not consume much resource, this is why i was wondering why it is affecting SPI on the other core. Yes, but due to other traffic it can potentially,...
View ArticleForum Post: RE: TDA4VH-Q1: Link Transfer for UDMA chaining - c7x core
Hi Brijesh, I am currently in the process of developing a test application for the C7x_1 core of the TDA4VH platform, specifically aimed at testing the UDMA chaining functionality. We already have a...
View ArticleForum Post: RE: TDA4VEN-Q1: TDA4VEN-Q1 on custom board doesn't start ROM boot...
Hi [quote userid="415688" url="~/support/processors-group/processors/f/processors-forum/1520837/tda4ven-q1-tda4ven-q1-on-custom-board-doesn-t-start-rom-boot-loader"] However, when monitoring UART0_TX...
View ArticleForum Post: RE: AM62A7-Q1: AM62A OSPI NAND ensure data reliability
Vaibhav, It's still not clearly that if some data storage in the block. But when will bad block occur and at that time what will happen? Like At that time data will loss or it will copy to next good...
View ArticleForum Post: RE: TDA4VEN-Q1: MIPI Lane / pos-neg swapping
Hi Furuna-san, I am really doubtful that CSIRX supports polarity change. and i think this is supported on CSITX, but let me confirm the same. Regards, Brijesh
View ArticleForum Post: RE: TDA4VM: J7200] SD UHS mode setting for tiboot3.bin
Hi Lee, Boot ROM loads tiboot3.bin in the lowest speed mode and hence there wouldn't be a problem there as we are not using UHS speed mode.However,tiboot3.bin cannot load tispl.bin because it is...
View ArticleForum Post: RE: [FAQ] AM6442, AM6441, AM6422, AM6421, AM6412, AM6411 and...
Hi Board designers, Information related to clock source (oscillator) placed on carrier board: Q. The oscillator is placed on the carrier board and the clock is connected through a connector to the...
View ArticleForum Post: RE: SK-AM62A-LP: RPI 7inch panel can be enable using prebuilt SDK...
Hi, What are the outputs for the following: modetest -M tidss ls -l /dev/dri/*
View ArticleForum Post: RE: J7200XSOMXEVM: J7200-EVM UART/LIN Multiplexer Configuration...
Hi Sarthak, [quote userid="650950" url="~/support/processors-group/processors/f/processors-forum/1518364/j7200xsomxevm-j7200-evm-uart-lin-multiplexer-configuration-for-gnss-data"]2. UART Device...
View ArticleForum Post: RE: [FAQ] AM625 / AM623 / AM620-Q1 / AM625-Q1 / AM625SIP / AM62A7...
Hi Board designers, Information related to clock source (oscillator) placed on carrier board: Q. The oscillator is placed on the carrier board and the clock is connected through a connector to the...
View ArticleForum Post: RE: TDA4VEN-Q1: TDA4VEN-Q1 on custom board doesn't start ROM boot...
Hi Diwakar, I’ve tried connecting to both UART0 and MCU_UART0 . Based on the documentation I’ve read, UART0 is the correct interface used by the ROM bootloader , so that’s the main one I’ve focused...
View ArticleForum Post: RE: TDA4VE-Q1: TDA4VE gpu driver and process priority
Hi Gaston, Looking into that. Will update you with some methods to try. But after talking with our team, I don't believe the issue is because of the priority of the k-threads but rather with the...
View ArticleForum Post: AM3352: Firmware compile error @ ubuntu 22.04
Tool/software: Fail to compile source code. Ubuntu version : 20.04 SDK: Graphics_SDK_setuplinux_hardfp_5_01_01_02.bin error information :
View ArticleForum Post: RE: TDA4VM: PC emulation mode :...
Hi, can you follow this link for sdk 7.1, https://software-dl.ti.com/jacinto7/esd/processor-sdk-rtos-jacinto7/07_01_00_11/exports/docs/vision_apps/docs/user_guide/ENVIRONMENT_SETUP.html Regards, Gokul
View Article