Forum Post: RE: Problems while running facedetect demo
Hello Erik,I am working on raw capture with OMAP-L138 LCDK too.I think that you might have misinterpret the second parameter in the following function:VPIFCaptureRawIntlineConfig(SOC_VPIF_0_REGS,...
View ArticleForum Post: RE: Memory mapping code, and constants from certain files to ddr...
Pubesh, Im trying to put all the NDK code into DDR memory. I can not use the library for the NDK because we have a custom board which uses a different phy and RMII interface, not MII. I have been...
View ArticleForum Post: RE: What's the criteria for a valid boot image?
Hi Rahul,I've been working with Eric on this issue and have reproduced the issue he describes and captured the information you have requested. As he mentions above, the issue occurs when erasing block...
View ArticleForum Post: RE: What will be the behavior in case DSP and EDMA3 controller...
Hello TI Team ,Can any one please help me to understand the details ...Ashish
View ArticleForum Post: RE: booting of am1808 from NAND flash
Harnek,You are still not using the nand partition info in bootargs. Also remove the SD card and try to bootup.
View ArticleForum Post: PWM on OMAL-l137 not generating output.
Using the PWM from the DSP is giving me Gray hair, I am usin the examples from the starter kit and now I have given up can't think of any other things to try.It is a simple PWM with asymetrical output...
View ArticleForum Post: RE: Simple McBSP application on C674x
Hi Sivaraj,thanks for your reply. I just found my mistake. Everywhere on my papers SCLKME is equal to zero(for the internal clock source) except in my code :-)
View ArticleForum Post: RE: OMAPL138BZWTD4 RoHS solder profile ?
HiWe don’t have device specific reflow profiles.We recommend them to refer to package specific app notes for reflow guidelines.http://focus.ti.com/lit/an/spraa99/spraa99.pdfThis is the first...
View ArticleForum Post: RE: Setup and hold time of the emif (omap l138b)
Hi,Please refer page no 857 to 865 in Technical referenc manual SPRUH77A www.ti.com/lit/ug/spruh77a/spruh77a.pdf for ASRAM example configuration (Toshiba’s TC55V1664FT-12) and followed by the NAND...
View ArticleForum Post: RE: Power off for Zoom™ OMAP-L138 EVM - Logic PD
Thanks for your post.Please refer the below document for Power-Up/Down Sequencing. (POWER_ON...
View ArticleForum Post: AM3505 MAC Address
Hello,Can someone tell me what range of values are programmed into the EFUSE for CONTROL_EFUSE_EMAC_LSB and MSB? Are these values guaranteed to be unique based on TI assigned IEEE Organizationally...
View ArticleForum Post: RE: SYSBIOS and SYSLINK for OMAPL138 experimenter kit
Hi Jiri,Thanks for clarification. I thought you were looking for DVSDK.From my understanding you can use the SDK released for LCDK.The Linux SDK of LCDK is having different Linux kernel version.You...
View ArticleForum Post: RE: exception when trying to write to certain memory locations.
Good afternoon,I am still no further on this issue. I guess that no body on here is able to help me as I am getting no responses, so what do you do when the TI emplyees on the TI support form cannot...
View ArticleForum Post: RE: NDK Jumbo packets - can be used with UDP?
No, I never solved this problem. I guessed from the EMAC architecture and NDK documentation that jumbo UDP packets are not supported, but I did not get confirmation from TI about this.Regards,Greg
View ArticleForum Post: Alternatives to bugg AISgen
We are using the DA830. Hence we use AISgen v0.8.2. I see that there is another AISgen, v1.11, but it has only even numbered ROM versions, while DA830 is an odd number. AISgen v0.8.2 is VERY buggy....
View ArticleForum Post: RE: NDK Jumbo packets - can be used with UDP?
Greg,NDK have jumbo packet buffer manager(PBM) for handling jumbo frames.It is capable of handling memory allocations only up to 3068 bytes (MMALLOC_MAXSIZE).Jumbo frames, i.e., packets typically...
View ArticleForum Post: RE: My C6748 failed to boot from I2C EEPROM
Hi Oliver,This could be due to pinmux issue. Please refer the below link for more detail.http://e2e.ti.com/support/dsp/tms320c6000_high_performance_dsps/f/115/t/269816.aspx
View ArticleForum Post: RE: Problems while running facedetect demo
Hello Katerina,Thanks for your input. You are right, I might have misinterpreted this parameter, but I have just tested different options for this parameter and in any case I am not able to get an...
View ArticleForum Post: RE: What will be the behavior in case DSP and EDMA3 controller...
Ashish Mishra, Yes, Your understanding is correct.For your 3rd scenario(accessing DDR via EDMA3 and DSP), You have to look in your code or design part. TI provides the EDMA test code in ompl138...
View ArticleForum Post: RE: Setup and hold time of the emif (omap l138b)
Hi Reshma,In addition to the above response, i hope, it would be useful for you to understand the A54SX08A Timing Characteristics of Actel SX-A Family FPGA Datasheet as...
View Article